Search results

I wanted your guy's opinions on tire brand preferences. My Goodyear 14.00R20 tires are getting pretty low on tread after nearly 60,000 miles on them. They have been pretty good with no major complaints. I won't go down to the 395's due to the loss of top speed, and yes I know I will lose a...

So I ran a test on my little heater. I throttled the engine with the hand throttle up a tad to high idle. I set the thermostat on the heater to a comfortable level. It would cycle on for about 2-3 mins then cycle off. It is small but really cranks out the HEAT! During the on cycle, it would...

Holy cow. I did not know that. Thanks Simp. BTW happy Thanksgiving everyone.

Thank you. The truck also has a lot more pep now. I guess when you have a part that is not self destructing it doesn't rob as much HP

I do believe it was. I played it safe, shut it down and I am very thankful I did. It was bad!

Here are the pics of the old fan clutch and I compared it to the new one. There was a pile of bearings on the ground where I took the fan off the old clutch to swap it to the new clutch. The front of my motor looks like my 3 year old daughter threw glitter all over my engine. Thank sweet little...

I do not. I was going to ask what everyone is using on these trucks.

It would be used mostly at idle but throttled up to a higher idle via hand cable. 2000 watt inverter running a small 1500 watt space heater over night that runs off and on. I sleep in my truck when I am in the field working and it gets cold in the dead of winter. Heater won't be running full...

I have the 70 amp 21SI installed now. Will the 110 amp 40SI work in our trucks? Thinking I needed a little more juice with the 2000 watt inverter.

Older post but I need some advice. I had the classic fan clutch rattle so I ordered the rebuild kit and the new style shutterstat. I had a shop install both. Fan clutch sounded fine at first but started getting progressively louder. 1500 miles later it is the worst is has even been. I took a...

Update: Sorry, haven't been on here much. I have been running around like a chicken with my head chopped off. So, I have found out a few things..... New rear main seal leaks....not nearly as bad but it leaks Truck will not shift from high range to low range. When I press the button on the...

Thank you!!

I had the rear main seal on my M925A2 replaced. It was BAD. The mechanic that dismantled the truck to replace the seal wound up sick and was off for an extended amount of time and a different mechanic finished the repair. I understand it sucks putting something back together that you did not...

Zipper boot. On my third set. Other than the mess it isn't a big deal. Mine has been bad and leaking for over a year. I will swap mine out again.....eventually

UPDATE So I serviced the air dryer yesterday. I think I figured out my problem. OMG. The internal filter on my air dryer was in pieces and the entire air dryer was coated in oil and debris. Unfortunately, I did not get photos due to being in grease up to my elbows. Needless to say, I took...

Where did you get the tank? I want it!

Does anyone have a larger fuel tank for an M923 that will fit in the stock tank location? I am in the market. If not, can anyone point me in the right direction of what I would need and who would have one? The 81-gallon tank is not big enough for some of my one-way hauls. I carry more fuel...

They also have the Tractor/Hydraulic fluid in stock and it is C-4 rated. How is your transmission after the change?

I drained the coolant and noticed it was extremely low. I ran Thermocure through the engine for 4 hours. It really worked. The water came out BLACK! I could only get about 6 gallons into the system when filling from the overflow tank. After 5 flushes and fills, I drained the water...

I will just go with this. Especially for the first change. I know I won't get all of the fluid out so there will be some mixing between the old and new. Second change I will go with the Transynd.