Search results

I make and market new canvas seat cushion covers for M 35, M39 5ton, 800 seies 5 ton and M37. PM or email me or see me at the Great MTA show in Sussex, NJ on March 18 and 19

This is a reply to Bottleworks post #20, For a fact, the Napa 1458 filters used on my adaptors cost between $13-$17 each depending on what price list you fall under, fleet account, etc. My kit uses 2 filters, the total cost of filters per oil change is $26 to $34 NOT $120 as you stated. If...

If it sits for long periods of time, it may or may not take longer to show oil pressure on the first start up. Accumulators leak down too. Everyone has there own thoughts and their own choice on what they plan to do to save their engine. JT out

Good to see you here Arthur, The older folks in this crowd know you to be very dedicated to the M35A2 trucks. Thank you for being available to help. JT out

The oil level will be at full or very close to full with my anti drain back filters installed on my oil filter adaptors. The napa/wix 1458 filters hold almost a quart, 2 holding 2 quarts nearly. So checking your dipstick cold, would yield full or slightly over. To the new oil adaptor owner...

What about this idea? 2 seconds to oil pressure and a bit simpler. JT

Hey, West Edmeston, I am in Ephrath, NY. I might be able to help you out. 1 hole or 2hole? JT

Cab bows, boys, don't argue. The trucks came with out cab wire bows for many years, my 1967 M51A2 has no cab bows, and no holes to put them in. And..... the cab cover is canvas an is not big enough for cab bows. Cab bows are a modern conveinience ince about 1968 or 1970. The cab cover for "With...

In the mean time, Oil is Napa 3311. primary 3511, gasket 5131. secondary 3512 or you can use 3540, gasket 5070. gasket for oil is 5119. These re all good numbers, don't let them say no. JT out

I will be at Sussex, with all the spin-on Multifuel adaptors , oil, primary ,and secondary. And filters for them. And AVM lockout hubs. And the seat cushion covers, bows, straps, shear pins, and light bulbs, and everything. PM for special requests. And I have Yankee Deuce with me to entertain...

The hole is where the governor parts are, and yes, it was a gasser truck, the fenders and hinged flaps say 1961 or older. They can be as oold as 1953, usually not before that cause the 50,51, 52, models were specialty trucks, like wreckers and augers, not cargo trucks. they had m-135s and M-211s...

The new electric wipers have sold for as much as $300. The heater unit without the rest of the kit could be worth $100 or some more. Your brake and air problems don't have to be related, probably are though. If you have no air pressure at all, you would normally still have a brake pedal and...

I had a oil leak start unexpectedly on a deuce with a REB kit. Got under there and found the speedometer drive unit had come out of the front of the transfer case. Discovered the REB kit gear had come loose and worked forward on the shaft and knocked the speedo drive right out of the transfer...

Kenny, you are one smart cookie!!!!! I drew a deuce out of Drum last Friday to a newbie in southern NY. As I was showing her around the truck , I mentioned to check the crossover fuel line and showed her where it was, to my surprize, it was crushed very flat on the primary side of the truck and...

Jim Henry trucks in Albemarle, NC at 704 983 5940. He has parts and complete generators and he works on them. Straight Shooter too. JT out

I think Zeligson Truck Equipmet is the company who originated that windshield. They were huge in refitting military trucks to oil field, pipeline, and power line contractor vehicles. Our M54 International was Zeligson re-manned and carried a Sterling Marauder pressure dgger, I ran it for years...

Kaiser Power, pm me with your address, I have some of those upper gaskets . I'll send you one or two. John T

I wonder if you might want to do an oil change, putting in 30 wt diesel engine oil? Those little plastic springs in your 15w-40 oil might have worn out. Just a thought. JT

I'm hoping he already sold it to me. JT

I remember that Deuce shear pins were headed at one time years ago. I also remember seeing pictures of them in a book somewhere. If you contact Memphis and ask the parts man to check with Max the owner, I think they will be able to answer your questions. Please be sure the shear pins are not...