-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Search results
-
O
How to bypass PCB? I am aware some HMMWV owners have done it. TOBASH
ummm. pretty sure he got shown the door a few months ago 😆- osteo16
- Post #57
- Forum: HMMWV Hot Rodding and Modification & Civilian H1
-
O
Smart Start Box Ground Cable
I'm not implying anything too logical here but, I don't have a ground wire on my box and it works fine.. I doubt disconnecting it would do any damage.. Just saying.... -
O
Looking up unit/service history via inventory number
So...what’s the numbers you found ???? -
O
Looking up unit/service history via inventory number
ummm... Tow Missile configuration humvee.......I don't think that's a unit number.. That a model number for your truck. Look for lettering inside door frame, drivers side. Also other insightful numerical things may be found under spray painted over areas ( sand/remove paint slowly to... -
O
Relocating the fuel filter assembly.. My idea..
does yours fluctuate 9-12 lbs like a pulse with engine running, then settle to around 9 with off, then bleed down ? I think my gauge is finicky -
O
Steel Soldiers giveaway sponsored by SECO
IN........ Many thanks SECO- osteo16
- Post #137
- Forum: Vendor Giveaways
-
O
Tire Bounce...
Ummm.. 1987,,, That would be a 33 year old rig, not 23 🤣 -
O
HMMWV Mods and Improvements
I would probably get this issue out of the MODS and Improvement thread and start a new thread with your title of choice.. "I left my key on all night, and now my HMMWV wont start.....HELP" That might work 😁 -
O
What have you done to your HMMWV today/lately
Was changing out the shoes on the wives H2... so I rolled a wheel over and tossed it on the 998.. Not quite big enough -
O
Remote Switch Control
Its the PCB...Protective Control Box.... Do a search, learn all kinds of good stuff about them Right Here on Steel Soldiers 😁 -
O
What have you done to your HMMWV today/lately
In hindsight, I might have tried a long ratchet extension.. But the punch was the right length and fit right on that small edge.. Few dings, mehhh -
O
What have you done to your HMMWV today/lately
Got the fan clutch unstuck 👊🏼 Thanks for all the info.... Ocho -
O
Rear Radius Rod
I have an idea.. New solution.. Two birds, one stone type of thing. :cool: -
O
What have you done to your HMMWV today/lately
Crawled out from under my dirty bastard 88’ M998 I was cleaning/prepping for paint to finish up renewing these beauties.. Ocho -
O
Rear Radius Rod
Well, to add to my plight.. I also have another radius tube I ordered months ago, and it is even shorter than the 10.87” model..it’s like 8 1/2”... My front radius rods are close to the 10” rods, but my rears are definately 12”.. guess I’ll do some calling around .. feel free anyone to look... -
O
Rear Radius Rod
Yes like that one, if that one is 12" and not the 10.87" that I've been finding everywhere. Im just concerned with the shorter length because my rod ends will most likely only screw into the radius rod up to the far end of the relief cut and not completely into the tube.. Not sure if it... -
O
Rear Radius Rod
Tearing down rear end on the 88’ M998. Want to replace the rear radius rods because one is bent and one has some bad threads... So I can’t seem to find anything longer than 10.87” as a replacement.. The ones on my rig are a solid 12” long.. Has anyone else had a problem with this or know... -
O
Leaking trani fluid?
Transmission modulator.. has o ring that might be leaking where it goes into transmission.. Can remove bracket holding it in and slide out to check/replace O ring.. looks like housing may be leaking though because of the bit of RTV smeared over it.. easy enough to get a new one and replace...