Search results

That is your glow plug relay. I'll save you the trouble of doing a search and the NAPA part number is ST85.

Does anyone know how hard this is? It's something I've always wanted to learn how to do and I know I can get the parts and do it a lot cheaper than taking it somewhere. I'd like to change out the gearing to a 3.73 gear and leave the gov-lock/detroit in the rear. If possible I've thought about...

Sounds like a possible ground issue. Have you checked the negative terminals on each battery?

Ok I have a question. My windshield washer has never worked since I got the truck from GL. The windshield wipers work fine on all speeds however and when I hit the washer tab the wipers cycle and there is a click from the wiper motor but no fluid comes out. I was looking on parts train and...

Does anyone if there is anyone in the Texas or South Louisiana area that sales these trailers? I am in need of one and haven't seen any come up on GL in a while and I'm kind of in need of one now. I have to go pick up a generator in Southern Mississippi and would like to use a trailer instead...

The O'Reilly part number is VM324 and mine works just fine. It comes with the hose that you will need as well.

I just looked at your pics and your light bar colors are backwards. The red is supposed to be over the driver's side and the blue over the passenger.

Hope someone answers. I asked the very same question and got now answer.

Wish you were closer. I would just buy it from you. I am looking for one of those.

Here is mine. I used a piece of instrumentation angle iron from Lowe's. You can get it one foot sections like I did or a 2 ft section and cut it in half. I then took some 5/16" x 1' all thread rod and some flat washers and nuts. Assembly is pretty straight forward. Because I'm building a...

I figured I would add some updated pictures of the truck with all the white marker stuff off. Here is what I have done so far. - Replaced all belts with Gates brand belts. - Replaced the glow plugs, glow plug relay, and installed a new glow plug relay card. - All new BFG All Terrains...

I used some of that paint from Rapco in a spray can it was too shiny. Is the stuff you are talking about the same paint?

Do they protrude past the front of the grill guard? That is one of my concerns since to me that's one of the points of the grill guard is to occasionally bump stuff. I'm worried that if the lights protrude past the front they will break should I ever give something a little tap. How are you...

I'm wanting a set of 4-3/4" ones so I can fit them in the grill. The 5" would be just a little bit too big so I think the 1/4" of leeway will help. I think to do what you want you will have to move the bridge plate. Once you do that you could possibly bolt them to the bumper.

What is it I need to tell an alternator shop that is doing the rebuilding? Isn't there something special they should be made aware of? I thought it was an isolated ground but I called one guy and he had no idea what I was talking about.

I saw a guy take some seats out of a 1996 Chevrolet and put them in without any problems. It's been at least 10 years though and I can't remember if he had to mounts any at all. The truck he put them in was a 1984.

I was in China in October and the Jeep Cherokee seems to be the predominant 4x4 over there.

I might get flamed but overall the the Land Cruiser is the safer bet. Very tough truck and lots of stuff to help with expedition runs. Check out IH8MUD.com - Your Online Offroad Tech Resource for more info on your Land Cruiser.

Sorry forgot to check on that. I will let you know. We could sell those as an each.

Lube - B6: $3.60 each with a minimum case order of 12 Air - PA2073: $11.00 each Fuel - BF856: $10.50 each I think to make it so I can do this without any problems if I make a mass order. So lets figure out a day of the month when I can place an order and I will do that to save on some...