Search results

Do you think these will fit 11.00 20's ? I'd like 4 x three rails and two singles for a 5 ton. Thanks.

Not quite. This is ignorance on behalf of the LEO - who is not up to speed on DoT regs. Any one with a wrecker endorcement or oversize CDL should know that rotating beacons/strobes are only legal on a moving vehicle if it is slow (< 40 in a 55) or excessively over width (just overwidth needs...

Nothing wrong with your work from my perspective, quite impressive. I'm not sure that wheels aren't made with a flat taper either. However I would have dimentioned the lug nut and not the height of the fitted lugnut, which will change subject to torque and wear of the hole as the nut seats in...

Yes I did but went straight to PM... I'll go back and do this - the e-mail option... BUT if he selected that his e-mail address be private.... I'll return to my original question. Thanks EDIT: Just went back and did the e-mail option. Thanks DH. Let's hope it doesn't get bounced...

I'm assuming he is nolonger active - no posts for 3 years.

Oz Spare tyres n trailers I'm still researching Oz wreckers, but I'd assume that the trailers were "upgraded" along with the trucks (from the 60's multi to the 70's 816), probably the same manufacturer but not sure. As far as the "M" number, that is not an American trailer (I don't think) so...

Understanding that e-mail addresses of S/S members are not available to the general masses only the site techno-nerds etc. Is there a a way that someone who hasn't posted in a couple of years, can be contacted on my behalf, with my question, for them to decide if they want to then contact me...

Darn it - now I'll have to go research Eddy Currents..... But thanks Rustygears for the terminology correction. Another cautionary tip. Don't weld 'through' your vise - ie., ground on the welding table/bumper etc., and then the positive on the work piece in the vise jaws. This may cause the...

Check garage/tag sales near army bases! Like Jeff said , there is also the stuff that actually dissapears from the BII itself as vehicles get upgraded, but the guys at the sharp end know it is good kit, so will move it over to the newer truck even if it isn't in the newer BII! When you find...

Connect or disconnect, that is the question. Whether it be ..... I always disconnect alternator and battery/'ies, I was told to do so many many years ago, but can't remember why. (Something to do with solid state huge-a-ma-flips or something and bad grounds/power surges, eddy currents and...

Well thanks for the research even though it makes me look like a complete monkeys armpity. I guess it was a tall tail, trying to impress me!

Sorry Jeff, this is all I have for now and excuse pics 3 and 4 - they are cut n pasted from a vid I found. And yes, the first two are multi fuels in Vietnam.

Well Sigo, that's all I have. It was a discussion with a local heavy recovery operator - not sure if it may have come from a trade journal. I'd hate to think I was 'sold a plum' but I could quite imagine this happening - I've seen the plenty of safety vids/pics of old style construction...

For airfied recoveries (aircraft) I think it was the M127. Narrow 5th wheel, step deck. (The M816 had a Freuhoff tandem-duel, tilt bed pintle trailer when used by the Australian Army.)

It pays to look twice.. I looked closer at your pic #2, comments in margin.... Not convinced that the chain is for the welding bottles, it works fine for holding the open the locker lid, but I only have one on the same side as Jeff! Jeffs truck light bar (goal post frame) only uses 2...

Ah - in lieu of the gun ring supports that my beacon uses now. Thanks. Now, any ideas on the mud flap adjacent brackets.

Noticed/found some holes/brackets and wondered if anyone knew what they might have been for... Bracket aft of the rear mudflap (metal part) on the underside of the body - would work for full height rubber flaps if there weren't the two piece ones. 5 holes per side in the bulkhead...

Agree with Doghead in that factory is always the safe bet, HOWEVER, since the manual was written, AND the then military budget dictated, there have been improvements in most technologies. The information IS out there. Cable ratings, bend radii, lubrication recommendations, termination...

Yes it will work, of course. If you have a plain, open drum winch - you could use bailer twine... In theory! If it's a smaller diameter than factory AND you have a level wind, then the cable tensioner WILL NOT work, unless you move the fixed pulley OR increase the pulley wheels size to make up...

Yard repairs - need a lift. ... so, tractor dragged into yard by the shop, but with no steering, had to pick up the back and move onto level conc pad for stability whilst stripping down. Needed to use stabiliser legs as I wasn't comfortable lifting whilst the truck listed to starboard with...