Search results

Check the frame around the steering box bolts for cracks, very common problem. Spring bushings bad can also cause it. Rick

They are all the same, It is a solvent. Do not use the vacuum line on your diesel or you will wipe out the vacuum pump, diesel engines do not produce vacuum. All of these suggestions are going on the assumption that you have a sticky lifter. Try this first but if it does not work do not be...

A Dana 44F is a Dana 44 carrier in a Dana 44 housing. It is a Dana 44 front, high pinion differential usually used in 78-79 Ford F250. Myself and many others have wheeled 44 fronts with 40 inch tires for years without destroying them. It is a matter of knowing how to drive. I have a 76 CJ-7 with...

Bill, I will go to bat for you. While I do agree with everyone about it being a downgrade it will be plenty strong as long as you do not overload it. Ford and Chevy both used the Dana 44 as a front in 3/4 ton applications at one time or another. I had one in a Ford 250 That had 40's on it and I...

Although I am not a big fan of additives I have seen Marvel Mystery Oil loosen up stuck lifters. This may not be your problem but it can't hurt to throw some in the oil and see what happens. Change the oil and filter at the same time, could be dirty oil. Rick

I tried Delk's one time for a fuel tank. Guy who answers phone tells me they have them used for 65.00, hollars to someone else who say's yea we got them, who is it? Phone guy replies it is a guy from Jersey, Guy in back says yup, got two of them 75.00 each. Needless to say Delks will be my last...

Sorry guy's I just, do not have time to read all the sticky's or go through the classifieds. I have no internet at home and I have limited time I can play at work. I apparently have a bad oil switch. 002A started cutting out yesterday for no obvious reason, bypassed oil switch and have had no...

You are going to find that four hours under water is about 3 3/4 hours more than fording standards. In salt water at that. You will find that rust is going to form everywhere and very quickly. Anything electrical that was in contact with the salt water will need to be rebuilt or replaced...

I had a "so called" good Samaritan get stuck in my septic drain field trying to drive through my lawn to get around a tree in the road. They were not helping anyone and were not looking to, they were sight seeing! They are lucky they did not get freakin shot since I was in no mood for that crap...

700R4 with G/V!! Yee-hawwwww

The one thing that has not been mentioned here yet is rust. Think rust, lots of rust. You are in NJ, think even more rust! Front fenders and inner fenders, rockers, door and door posts, rear quarter panels and tailgates. I didn't mention the floor because it is probably already an aluminum...

Unless you are looking for a helper just find a Wally world parking lot or similar. Rick

I'll Bet you sold it to a guy from the g838, guy named Matt? I know he was looking at one in Kansas. Rick Then again, Matt doesn't have long hair? Maybe not then. Kansas must have a bunch of 715 for sale.

I think you need to read up on swr a bit, The ratio to look for is 1:1, 1: 5 is bad and 1:0 is impossible. VSWR conversion calculator

With the parts I am seeing removed from the engine I am guessing the engine is bad. Check that out before going too far. Definitely before putting anything back on. They did not disassemble it for nothing. Put a socket on the front balancer bolt and go back and forth with it and see if the crank...

Transmitting with no load (broken antenna) may have fried the finals in the transmitter. You need to hook up a dummy load and check to see if it is actually still transmitting. Rick

Does anyone REALLY think that the plaintiff's lawyers and the defendant's lawyers are not friends and fully intend to drag this out until nobody has any money left? The only winners here will be the lawyers and unless you are independently wealthy I can assure you that they have more money to...

A 6.2 is just about the same weight as a big block so the heavy duty ones will work. That said the heavier the better. I put a 502 big block on one of the ones shown with the single runner out to two front wheels, will not do that again. With exhaust manifolds that is a 1000 lb. setup and it...

I talked to this guy at Gilbert and he did not have any there but he does have them. He told me around 40.00 for them NOS. I have to get in touch with a friend of mine who knows him and will have his number. Rick

I had a guys card but lost it. I need one for mine also, I will make a couple of calls and get his name and number. The carbs are out there and price is not bad. Rick